Article Index

1. Adjustment Methods

Network adjustment is the method by which the misclosure is distributed back into the newly created elevations. The adjustment methodology should reflect error behavior and be repeatable. There are a number of approaches, some better than others. These are summarized in Table E-1.

 

Table E-1
Method Premise Advantage Disadvantage
Ignore Don't adjust anything. Simple; repeatable. Ignores errors.
Arbitrary Place error randomly in one or more raw elevations. Simple.  Not repeatable. 
Judgement call Decide based on field conditions, equipment, and personnel, which raw elevations probably had more error. Considers error behavior.  Not repeatable; not rigorous; requires personal knowledge of entire project.
Equal distribution Distribute errors equally among raw elevations. Simple; repeatable.  Treats random errors systematically; assumes all errors are positive or negative.
Proportional distribution Distribute errors based on sight distances. Simple; repeatable; accounts for greater error in longer sights.  Treats random errors systematically; assumes all errors are positive or negative; requires distances.
Least squares Full statistical approach. Allows full random error modeling; can mix different quality measurements; provides adjusted elevation uncertainties. Most complicated and computation-intensive.

 

For simple networks, Figure E-1(a), the Equal or Proportional distributions generally give satisfactory results. However in complex networks which have additional measurements between points, Figure E-1(b), using the Equal or Proportional methods is too cumbersome if not impossible.

e 1
Figure E-1
Leveling Networks


In a simple network, each point has only a single raw elevation. In a complex network, each point can have multiple raw elevations based on connections to other points. The raw elevations differ because their respective random errors accumulated along different paths to the point. The best way to model and compensate the errors is using least squares.

The concept of least squares is beyond the scope of this discussion since we are limiting it to simple networks. We will look at applying the Equal and Proportional methods.


2. Example 1

A level network, Figure E-2, starts at BM Q, whose elevation is 821.12 ft, travels to points A, TP1, B, and closes back on BM Q. The raw field elevations are shown on the diagram; red numbers are the total of the BS and FS distances between points.

 

e 2a
Figure E-2
Example Network

 

Adjust the network using the Equal and Proportional distributions; compare their results.

Using Equation D-4, the network misclosure is: M = 820.03 ft - 820.12 ft = -0.09 ft

a. Equal distribution

The Equal distribution applies an equal part of the misclosure to each raw elevation. It is a cumulative correction since each corrected elevation affects following raw elevations by a like amount.

 eqn e 1      Equation E-1
M: misclosure
n: number of raw elevations determined
i: elevation number

 

Four raw elevations were established counting the closing elevation on BM Q. Substituting this network's values in Equation E-1: 

e ex a1

 

“i” is the seqential number of each elevation in the order they were created; A is 1, TP1 is 2, etc.
The adjusted elevations (computed to an additional decimal place minimizing rounding error) are:

e ex a2

b. Proportional distribution

The Proportional distribution applies a part of the misclosure to each raw elevation based on sight distances. It is also a cumulative correction since each corrected elevation affects following raw elevations by a like amount. 

 eqn e 2      Equation E-2
M: misclosure
D: total BS and FS distances
d: cumulative distance to current point

 

The total distance, D, around the loop is 75'+300'+175'+550' = 1100'. Setting up Equation E-2 for this network:

e ex b1

The adjusted elevations (computed to an additional decimal place minimizing rounding error) are:

e ex b2

c. Comparison

Table E-1
Point Equal Proportional
A 827.642 827.626
TP1 818.115 818.101
B 815.798 815.775
BM Q 820.120 820.120

 

d. Comments

(1) Math check

Computing back into BM Q for both methods provides a math check. A common mistake is to forget to reverse the sign of the misclosure. If that were the case, the adjusted elevation at BM Q would be 0.18' too low - twice what it was indicating corrections were applied in the wrong direction.

(2) Skipping points

Although the adjusted elevation of TP1 was computed in both methods, it can be skipped since it's only a temporary point. However, any elevation determined in the field, temporary or permanent, must be included in the count (n) for the Equal distribution and the distances through them for the Proportional distribution.

(3) Same results?

If the sight distances between points are all equal then the Proportional distribution will result in the same adjusted elevations as the Equal distribution. 

(4) Random errors only

Misclosure is a result of random errors - mistakes must removed and systematic errors compensated. If they aren’t, then the quality of the adjusted elevations will be degraded. For example, assume the same network but the closing elevation for BM Q was 825.10', 4.98' too high, Figure E-3. A misclosure that large is usually the result of one or more mistakes.

e 3
Figure E-3
Network with a Mistake

 

Using an Equal distribution, the equation set up is:

e d 4

If the error occurred between TP1 and B, the raw elevations of A and TP1 won’t be affected by it. Nor will the raw elevation difference between B and BM Q.

If the network is adjusted without first eliminating the mistake, then parts of it will be pushed into all raw elevations. Instead of isolating the error, its effect is spread through the entire network.

If the misclosure is larger than reasonable, look for mistakes or unresolved systematic errors. If neither can be found, or the misclosure is still unreasonably large, then part or all of the network may need to be re-run. 


3. Example 2

The diagram below shows a link circuit running from BM Lima to BM Hotel.

are instrument locations.
TP# is a temporary turning point.
Green numbers are elevations determined in the field.
Blue numbers are BS and FS distances in paces measured by the rod person.
          The rod person's pace count is 41.5 paces per 100.0 ft.
Known elevations are BM Lima = 926.49' and BM Hotel = 953.41'

Determine adjusted elevations of non-turning points by:

Equal distribution

Proportional distribution

Because the network ended on BM Hotel, we use its measured and known elevations to determine the misclosure, M:

M=953.49' - 953.41'= +0.08'

a. Equal distribution

A total of 7 elevations were established. From Equation E-1:

Applying the equation to each non-turning point:

We don't need to adjust the turning point elevations, we just need to keep track of the sequential number of the elevation that is being adjusted. As a math check, we always compute the adjusted elevation of the closing point.

b. Proportional distribution

The total sight length of the network is:

(53p+54p+39p+39p+62p+61p+46p+47p+29p+28p+66p+68p+31p+32p) = 655p

We could use the rod person's pace count to convert 655p to feet, but we don't need to. Why not? Because the paces will cancel in the elevation adjustment equation.

From Equation E-2:

To adjust the elevation of A:

Cumulative and total distance units cancel.

Before continuing with the rest, let's compute the cumulative distance to each point so our adjustment equations don't become too cumbersome.

A: 54p+54p = 107p

TP1: 107p+39p+39p = 185p

B: 185p+62p+61p = 308p

TP2: 308p+46p+47p = 401p

C: 401p+29p+28p = 458p

D: 458p+66p+68p = 592p

BM Hotel: 592p+31p+32p = 655p

Although we didn't adjust turning points elevations, we included the distances through them to points that were adjusted.


Self Study: Level Network Adjustment

Comments (0)

There are no comments posted here yet